Van essentials

Van loading door dimensions: why the opening matters

Why the rear door aperture is often smaller than the load space, and how to measure it yourself.

By Bilal Javed Published 4 min read

Van loading door dimensions are the clear width and height of the rear and side door openings, and on most vans they are smaller than the load space behind them. That means an item can be short enough and narrow enough for the inside of the van and still fail at the doors. Checking the opening first saves wasted hire time.

Why the opening is smaller than the load space

A panel van's body is a box with a strong frame around each opening. The rear door frame, the roof cross-member above it, the hinges, the door seals and sometimes the tail light housings all sit inside the outline of the body. So the clear hole you can push something through is narrower and lower than the space just inside it.

On some vans the difference is a few centimetres. On others, particularly where the roof slopes down toward the back or the rear bumper step is high, the opening can be a lot smaller than the load height.

How to measure a door opening properly

  1. Open the doors fully. Release any catch that lets the doors swing past 90 degrees.
  2. Measure the clear width. Hold the tape across the opening at its narrowest point, usually between the door seals or hinge mounts. Check at the bottom, middle and top, because many openings are narrower at the top.
  3. Measure the clear height. From the load floor (not the bumper) to the lowest part of the frame above. Watch for a roof cross-member or a light unit hanging down.
  4. Note the floor height. Measure from the ground to the load floor. It does not change what fits, but it tells you how high you have to lift things.
  5. Repeat for the side door. Slide it fully open and measure width and height the same way.

Write down the smallest figure for each, not the average.

What the door opening limits

As an item slides in through the back, the dimension along the van can be anything up to the load length. It is the other two dimensions, the item's cross-section, that have to pass through the opening. A wardrobe lying on its back going in feet first needs its width and its depth to clear the door. Stand it upright and its height has to clear the door height instead.

That is exactly what the Van Load Fit Calculator checks for every orientation. If it reports "fits inside, but not through the doors", the item is fine for the load space but the opening is the problem.

Rear doors versus side doors

Rear doorsSide loading door
Typical widthClose to the width between the wheel archesUsually much narrower, often under a metre
Typical heightClose to the load height on high-roof vans, less on standard roofsOften lower than the rear opening
Best forLong and bulky items, pallets, appliancesBoxes, tools, reaching the front of the load
Watch out forLow roof cross-member, high floorBulkhead and seat position limit length

A van with two side doors gives you more ways to reach the load, but it does not make either opening bigger.

Tricks for items that are close

  • Tilt it. An opening's diagonal is longer than its width or height. A low, wide item can sometimes go in tilted at an angle and be laid flat once inside, as long as the load space has room to turn it.
  • Take bits off. Legs, feet, handles, doors and headboards often unscrew. A few centimetres is all you need.
  • Unpack it. Original packaging can add several centimetres. Blankets and film take less room and protect just as well.
  • Choose a box van. Luton vans normally have a rear opening close to the full internal width and height of the box, plus a lower floor if they have a tail lift.

Common mistakes

  • Measuring the outside of the doors instead of the clear opening.
  • Measuring from the bumper step instead of the load floor.
  • Assuming every van of the same model has the same opening. Roof height and body options change it.
  • Forgetting that a tail lift platform, a step or a rear bumper can stop an item being slid in flat.

Safety at the rear doors

Most loading injuries happen at the doors, not inside the van. Lifting a heavy item up to floor height and through a tight opening puts strain on your back and fingers. Use two people, a ramp or a tail lift for anything heavy, and never stand under an item being lifted. Once it is in, strap it to the tie-down points, because an unsecured item near the doors can slide out when they are opened at the other end. DVSA's guidance on securing loads covers this.

Frequently asked questions

Is the rear door opening the same as the load width?

No. On most panel vans the opening is smaller than the load space in both width and height, because the door frame and roof structure sit inside the body.

Are side loading doors big enough for furniture?

They are usually much narrower than the rear opening, often less than a metre wide. They are handy for boxes and for reaching the front of the load, but rarely for large furniture.

Do barn doors open fully?

Many rear doors open to about 180 degrees, and some to around 250 degrees with a release catch. Fully opened doors do not reduce the opening, but doors that only open part way can get in the way of long items.

Where can I find door sizes for a hire van?

Ask the hire company. Some publish them alongside load length and volume. Otherwise measure at collection.

Sources and further reading

About this guideWritten for LoadFit by Bilal Javed. We check facts against official sources such as GOV.UK and DVSA where rules are involved, and we update guides when those rules change. If something here is out of date or unclear, please let us know.